Output feedback controller for polytopic systems exploiting the direct searching of the design space

This paper deals with the problem of designing a robust static output feedback controller for polytopic systems. The current research that tackled this problem is mainly based on LMI method, which is conservative by nature. In this paper, a novel approach is proposed, which considers the design space of the controller parameters and iteratively partitions the space to small simplexes. Then, by assessing the stability in each simplex, the solution space for design parameters is directly determined. It has been theoretically proved that, if there exists a feasible solution in the design space, the algorithm can find it. To validate the result of the proposed approach, comparative simulation examples are given to illustrate the performance of the design methodology as compared to those of previous approaches.     

Deep reinforcement learning-based cooperative interactions among heterogeneous vehicular networks

Most real-world vehicle nodes can be structured into an interconnected network of vehicles. Through structuring these services and vehicle device interactions into multiple types, such internet of vehicles becomes multidimensional heterogeneous overlay networks. The heterogeneousness of the overlays makes it difficult for the overlay networks to coordinate with each other to improve their performance. Therefore, it poses an interesting but critical challenge to the effective analysis of heterogeneous virtual vehicular networks. A variety of virtual vehicular networks can be easily deployed onto the native network by applying the concept of SDN (Software Defined Networking). These virtual networks reflect their heterogeneousness due to their different performance goals, and they compete for the same physical resources of the underlying network, so that a sub-optimal performance of the virtual networks may be achieved. Therefore, we propose a Deep Reinforcement Learning (DRL) approach to make the virtual networks cooperate with each other through the SDN controller. A cooperative solution based on the asymmetric Nash bargaining is proposed for co-existing virtual networks to improve their performance. Moreover, the Markov Chain model and DRL resolution are introduced to leverage the heterogeneous performance goals of virtual networks. The implementation of the approach is introduced, and simulation results confirm the performance improvement of the latency sensitive, loss-rate sensitive and throughput sensitive heterogeneous vehicular networks using our cooperative solution.     

A survey on fog computing for the Internet of Things

Fog computing has emerged to support the requirements of IoT applications that could not be met by today’s solutions. Different initiatives have been presented to drive the development of fog, and much work has been done to improve certain aspects. However, an in-depth analysis of the different solutions, detailing how they can be integrated and applied to meet specific requirements, is still required. In this work, we present a unified architectural model and a new taxonomy, by comparing a large number of solutions. Finally, we draw some conclusions and guidelines for the development of IoT applications based on fog.     

Evaluation of hydrodynamic behavior of the perforated gas distributor of industrial gas phase polymerization reactor using CFD-PBM coupled model

A 2D computational fluid dynamics (Eulerian–Eulerian) multiphase flow model coupled with a population balance model (CFD-PBM) was implemented to investigate the fluidization structure in terms of entrance region in an industrial-scale gas phase fluidized bed reactor. The simulation results were compared with the industrial data, and good agreement was observed. Two cases including perforated distributor and complete sparger were applied to examine the flow structure through the bed. The parametric sensitivity analysis of time step, number of node, drag coefficient, and specularity coefficient was carried out. It was found that the results were more sensitive to the drag model. The results showed that the entrance configuration has significant effect on the flow structure. While the dead zones are created in both corners of the distributors, the perforated distributor generates more startup bubbles, heterogeneous flow field, and better gas–solid interaction above the entrance region due to jet formation.     

A study on the monitoring model development for quality measurement of internet traffic

The recent trend of integration among new network services such as the long-term evolution (LTE) based on internet protocol (IP) needs reputable analyses and prediction information on the internet traffic. The IP along with increased internet traffics due to expanding new service platforms such as smartphones will reflect policies such as network QoS according to new services. The establishment of monitoring methods and analysis plans is thus required for the development of internet traffics that will analyze their status and predict their future. The paper with the speed of Internet traffic model is developed for monitoring the state of the experiment and verified. The problem is that the proposed service Internet service provider (ISP) to resolve the conflict between the occurrences can be considerably Internet traffic and that the state of data may be helpful in understanding. The paper advancement policy to reflect the network traffic volume of Internet services and users irradiation with increased traffic due to the development and management of the analysis was carried out experimental measurements.     

Analysis of adhesively bonded CFRE composite scarf joints modified with MWCNTs

The main objective of the present work is to improve the performance of bonded joints in carbon fiber composite structures through introducing Multi-Walled Carbon Nanotubes (MWCNTs) into Epocast 50-A1/946 epoxy, which was primarily developed for joining and repairing of composite aircraft structures. Results from tension characterizations of structural adhesive joints (SAJs) with different scarf angles (5–45°) showed improvement up to 40% compared to neat epoxy (NE)–SAJs. Special attention was considered to investigate the performance of SAJs with 5° scarf angle under different environments. The tensile strength and stiffness of both NE-SAJs and MWCNT/E-SAJs were dramatically decreased at elevated temperature. Water absorption showed a marginal drop of about 2.0% in the tensile strength of the moist SAJs compared to the dry one. Cracks initiation and propagation were detected effectively using instrumented-SAJs with eight strain gauges. The experimental results agree well with the predicted using three-dimensional finite element analysis model.     

Stochastic free vibration analyses of composite shallow doubly curved shells – A Kriging model approach

This paper presents the Kriging model approach for stochastic free vibration analysis of composite shallow doubly curved shells. The finite element formulation is carried out considering rotary inertia and transverse shear deformation based on Mindlin’s theory. The stochastic natural frequencies are expressed in terms of Kriging surrogate models. The influence of random variation of different input parameters on the output natural frequencies is addressed. The sampling size and computational cost is reduced by employing the present method compared to direct Monte Carlo simulation. The convergence studies and error analysis are carried out to ensure the accuracy of present approach. The stochastic mode shapes and frequency response function are also depicted for a typical laminate configuration. Statistical analysis is presented to illustrate the results using Kriging model and its performance.     

云杉八齿小蠹Ips typographus L.虚拟模型构建方法研究

本文以云杉八齿小蠹Ips typographus Linnaeus为例,经标本选取,观察虫体整体形态,绘制整体结构草图,电子显微镜观察局部、得到局部数字图像,分别建立虫体每一部分的高精度细节。把模型每部分拼装在一起组成整体模型,构建出了云杉八齿小蠹三维虚拟昆虫数字化模型。     

A model- and simulation-based approach for tolerancing and verifying the functional capability of micro/nano-structured workpieces

The evaluation of functional features of manufactured workpieces is based on GO- and NO-GO-test results, which are obtained by comparing measured geometric characteristics with nominal dimensions and tolerances specified by the designer. These geometrical specifications are based on a tolerancing system, which was originally defined for the function mating capability. Against the background of upcoming lots of other new functions (like reduction of flow resistance, light absorption, reduction of friction, diffraction of light, self-cleaning or mass transmission) are to be realized with our products – particularly by micro- and nano scaled features. If the verification process will deliver the prediction of the achievable degree of functionality, the usability of a part can be assessed more accurately and in consequence quality and economics can be improved. So, a new principle for tolerancing and verifying turns out to be necessary. In this paper the fundamental deficit of the actual tolerancing and specification systems GPS and ASME Y14.5 is derived and the path for enlarging the system by preposing a functional model is shown. To verify the functional capability of the workpieces an approach based on simulations done with the parameterized mathematical–physical model of the function is suggested. Advantages of this approach will be discussed and demonstrated by examples with microstructured inking rolls, crankshafts and injection valves.     

Digital Microfluidics for Manipulation and Analysis of a Single Cell

The basic structural and functional unit of a living organism is a single cell. To understand the variability and to improve the biomedical requirement of a single cell, its analysis has become a key technique in biological and biomedical research. With a physical boundary of microchannels and microstructures, single cells are efficiently captured and analyzed, whereas electric forces sort and position single cells. Various microfluidic techniques have been exploited to manipulate single cells through hydrodynamic and electric forces. Digital microfluidics (DMF), the manipulation of individual droplets holding minute reagents and cells of interest by electric forces, has received more attention recently. Because of ease of fabrication, compactness and prospective automation, DMF has become a powerful approach for biological application. We review recent developments of various microfluidic chips for analysis of a single cell and for efficient genetic screening. In addition, perspectives to develop analysis of single cells based on DMF and emerging functionality with high throughput are discussed.